sisli escort
maltepe escort bayan
FeaturedHome Improvement

Things You Need To Know About The Roof Inspections

The roof of your home is your first line of defense against extreme weather conditions. Be it a foot of snow dropping or strong winds tearing through your hometown. When a homeowner blindly places his trust in the roof and delays roof inspections until a few signs of a leak in the ceiling appears, there is a great chance of facing much bigger problems down the road.  This article tells you how you can spare yourself a headache in the future by having your Roof Inspection on regular basis. The most durable of all the roofing materials is rubber roofing. It lasts longer with a life expectancy of more than 50 years.

When Should You Schedule Your Roof Inspection?

When it comes to the safety and maintenance of your rubber roof, it is suggested to go for a rubber roof inspection twice a year. The best seasons to go for rubber roofing near you are either Spring or Autumn when the weather is mild. It would be a great idea to carry out your roof inspection after rainfall, hail, or high wind. This will help you check the quality of your roof and how well the water drained away. However, it should not be the only time you care about the health of your roof.

Timing Is The key

Roof installations or repairs should be avoided during frigid temperatures such as many shingles cannot be sealed down properly in winters. Moreover, repairing icy roofs can be treacherous. Thus, the problems uncovered a late need to be fixed late in spring. Also, the roof repairs should be initiated in the fall so they can be completed by the next spring.

Inspection on a rubber roof

The tips mentioned below will help you do a better inspection of your rubber roof.

Visually Check-Up

If your roof is flat, walking your roof is going to be a great start to your inspection. You should be looking for any sign that can stand out as an issue such as a tear, hole, or puncture in the membrane. Leaking roofs are not always a mystery, however, most of the time they can easily detect by just a visual check-up. Carefully check the gutters and drains to make sure they are allowing water to pass on easily and are not clogged. While you walk on the rubber roof, pay attention to the constancy of the insulation below the rubber. This can be identified if an area of your roof compresses more when stepped on. This could be evidence of a leak.

Termination And The Coping Caps

The places in your roof where termination bars are used have the potential to leak because of shrinkage of the rubber with time. Other reasons can be loosened or missing fasteners, and the deteriorated masonry above the bar. During your inspection, you should also pay attention to the coping caps. Check for areas that need to cut during the installation of a new roof such as the inside or outside corners of a house or building. Moreover, check for the gaps between the sections as well. These sections depend on the areas. Where pieces are put together such as caulking or sealant.

Debris And The Damage

Attention should paid to the cleanness of your roof. You should put effort to keep your roof clean from any debris like leaves or sticks by using special equipment. Tools like a small crew or metal shavings can use for such activity. However, these tools should used properly and with great care as they can puncture or cut the rubber. Any puncture or depression in the roof can cause leakage that needs to inspect carefully.

Transitions, Seams, And Penetrations

The most common cause of leakage in rubber roofs is because separation of seams. Seams are found at the junctions of the deck sheet and parapet wall. Seams are made and adhere to the rubber sheets differently. EPDM seams are produce by priming rubber sheets using the rubber tape that makes the rubber sheets adhere to each other. Moreover, flashing can prime and adhere to the rubber sheet. Although, in both cases, the durability and adhesion of the seam are dependent on the temperature and moisture present at the time of the first installation. To inspect properly, check for the seams that are separate around flashing and on deck sheets.

Professional Roof Inspection

A roof inspection can divide into four facets that are as follows:

Structural Inspection

This type of inspection includes the checking of all structural elements of a Euroshield Roofing Calgary. Here the inspector will look for the uneven roof planes or any cue of sagging. The inspector may also look for any venting in your attic that can increase the risk of ice dams at the edges of the roof.

Material Inspection

Material inspection includes the checking of loose or missing shingles, moss, rust, and any missing component such as missing flashing or fasteners.

Interior Inspection

As the roof leaks ultimately damage the interior of your home. The inspector needs to check the interior ceiling, the attic, and walls for water stains to get the signs of water making its way into your home.

Workmanship Inspection

This inspection includes problems in workmanship that increase the risk of leakage such as improper flashing would be a red flag.


Taking great care of your rubber roof will not only increase its life span but also avoid costly emergency repairs.

Leave a Reply

Your email address will not be published. Required fields are marked *

vip escortlar
anadolu yakası escort